6X2 CHANNEL RF wireless remote control system with 12 button transmitter & receiver for home automation. 12 CH RF radio remote control switch DC 12V 1000M /3000ft control distance for electronics 315MHz. This 2 channel DC RF wireless remote control system can used to control lights, motor, fans, electrically operated doors/locks blinds or other appliances automatically. It is easy to install and use. The remote control switch has 2 buttons, and works with toggle, latched, momentary and momentary + toggle 4 control modes. Its control distance is about 100 meters away. It should be a good choice for you. Just take it away! Note: Customized design is acceptable, we have professional technology-support! Wireless control, easy to install. Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC 110240V or DC 028V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. With characteristics of over current protection, short-circuit protection and temperature protection. Audible / visual indication. Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology. Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code. One/several transmitters can control one/several receivers simultaneously. If you use two or more receivers in the same place, you can set them with different codes. Transmitting Frequency: The default frequency is 315MHz. Control Modes: Toggle, Momentary, Latched, Momentary + Toggle. Coding Type: Fixed code. Coding Setting: By learning. Power Supply (Operating Voltage). Working Voltage Range of Relay: AC 110240V or DC 028V. PCB size: 74mm x 52mm x 24mm. Case size: 79mm x 58mm x 35mm. Maximum Working Current: 10A. Remote Control Distance: 1000m / 3000ft (theoretically). Encode: Fixed code by Soldering. Unit size: 145mm x 44mm x 25mm. Power Supply: 1 x 6F22 -9V battery (included, can be used for 12 months). If you want to use other control modes, do as following operation. Setting control mode Toggle: Only connect Jumper-2. Control mode Toggle: Press -> On; Press again -> Off. Press button A: Turn on the relay (connect B and C, disconnect A and B) Press button A again: Turn off the relay (disconnect B and C, connect A and B). Setting control mode Momentary: Only connect Jumper-1. Control mode Momentary: Press and hold -> On; Release -> Off. Press and hold button A: Turn on the relay (connect B and C, disconnect A and B) Release button A: Turn off the relay (disconnect B and C, connect A and B). Setting control mode Latched: Do not connect Jumper-1 and Jumper-2. Control mode Latched: Press -> On, another relay Off; Press another button -> Off. Press button A: Turn on the relay (connect B and C, disconnect A and B) Press button B: Turn off the relay (disconnect B and C, connect A and B). Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2. Control mode Momentary (Channel 1): Press -> On; Press again -> Off. Press and hold button A: Turn on relay 1 (connect B and C, disconnect A and B) Release button A: Turn off relay 1 (disconnect B and C, connect A and B) Control mode Toggle (Channel 2): Press and hold -> On; Release -> Off. Press button B: Turn on relay 2 (connect B and C, disconnect A and B) Press button B again: Turn off relay 2 (disconnect B and C, connect A and B). We have learned remote control to the receiver. If you dont want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver. Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored codes have been deleted successfully. Learning the button of remote control. 1 Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING. 2 Press button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful. Receiver1:press button 1 to learn. Receiver2:press button 3 to learn. Receiver3:press button 5 to learn. Receiver4:press button 7 to learn. Receiver5:press button 9 to learn. Receiver6:press button 1 to learn. 3 When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued. 4 The receiver can learn several remote controls with different codes. 12 x Receiver: H2-DC12 (2 Channel / Four Control Modes). 1 x Transmitter: HR-12. 1 x User manual. We don’t accept the cheque. The images are for reference only. Please take the item you get as the standard. Please repack the item carefully. During our weekend, you can get the reply in 48 hours. If you we are not satisfied with the product or service , please contact me and don’t give us negative or natural feedback, We must give you a satisfactory solution. Your action will help us offer our milk and bread. The item “DIY 12 Channel Wireless Remote Control Receiver Switch DC12V Relay on/off led” is in sale since Monday, April 14, 2014. This item is in the category “Consumer Electronics\Surveillance & Smart Home Electronics\Other Smart Home Electronics”. The seller is “13yuanyuan” and is located in , . This item can be shipped worldwide.
- Country/Region of Manufacture: China
- Connectivity: Wireless
- Model: 6XH2DC-HR12
- Country of Manufacture: China
- MPN: Does Not Apply
- Brand: mytang